Free Preparation Discussions
MENU
HPE6-A73 Exam Questions
- Topic 1: Explain Aruba solutions integration and configuration concepts/ Manage, maintain, optimize, and monitor the wired network solution
- Topic 2: Explain QoS Aruba Switch features and configuration concepts/ Explain multicast features and configuration concepts
- Topic 3: Analyze data that represents the operational state of a network and determine the appropriate action/ Explain Aruba Switch security features and configuration concepts
- Topic 4: Given a scenario, identify a network failure/ Given a scenario with a design and/or customer requirements, determine an appropriate implementation plan
- Topic 5: Given the implementation plan, explain how to configure Layer 2 technologies/ Given an implementation plan, explain how to physically configure the switches
- Topic 6: Given an action plan to remediate an issue, determine the implications to the network state/ Determine a strategy to implement configuration management
Free HP HPE6-A73 Exam Actual Questions
Note: Premium Questions for HPE6-A73 were last updated On Jul. 05, 2025 (see below)
An administrator has an aggregation layer of 8325CX switches configured as a VSX pair. The administrator is
concerned that when OSPF network changes occur, the aggregation switches will respond to the changes
slowly, and this will affect network connectivity, especially VoIP calls, in the connected access layer switches.
What should the administrator do on the aggregation layer switches to alleviate this issue?D18912E1457D5D1DDCBD40AB3BF70D5D
'BFD tests the connectivity between two IP addresses in a BFD session. BFD reports when connectivity is lost. The router (or routing switch) can then use that information to take the appropriate actions, depending on the functions to which you have tied BFD'
Examine the attached diagram
Two AOS-CX switches are configured for VSX at the access layer, where servers attached to them. An SVI interface is configured for VLAN 10 and serves as the default gateway for VLAN 10. The ISL link between the switches fails, but the keepalive interface functions. Active gateway has been configured on the switches.
What is correct about access from the servers to the Core?
A company has recently upgraded their campus switching infrastructure with AOS-CX switches. They have
implemented 802.1X authentication on access ports where laptop and IOT devices typically connect. An
administrator has noticed that for POE devices, the AOS-CX switch ports are delivering the maximum wattage
to the port instead of what the device actually needs.
Concerned about this waste of electricity, what should the administrator implement to solve this problem?
Examine the network topology.
Company XYZ has two connections to a service provider (ISP1). Here is the configuration of Router1:
Here is the configuration of Router2:
Based on configuration of Router1 and Router2, which BGP metric is being manipulated?
- Select Question Types you want
- Set your Desired Pass Percentage
- Allocate Time (Hours : Minutes)
- Create Multiple Practice tests with Limited Questions
- Customer Support
Callie
4 days agoRupert
19 days agoJohnetta
27 days agoCyndy
2 months agoEmmett
3 months agoCrista
3 months agoUlysses
4 months agoRueben
4 months agoEna
4 months agoLauran
5 months agoJudy
5 months agoAudra
5 months agoMeaghan
6 months agoEstrella
6 months agoValentin
6 months agoVeronique
6 months agoSantos
7 months agoMelynda
7 months agoSabina
7 months agoJacquline
7 months agoLavonna
7 months agoBarney
8 months agoShaquana
8 months agoCandida
8 months agoTiera
8 months agoMicheal
8 months agoSol
9 months agoPolly
9 months agoLemuel
9 months agoMaryln
9 months agoRossana
9 months agoCarin
10 months agoReena
10 months agoQuinn
10 months agoLindsey
11 months agoCorinne
12 months agoFredric
1 years agoDarnell
1 years ago