BlackFriday 2024! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions

Fortinet Exam NSE7_PBC-7.2 Topic 1 Question 25 Discussion

Actual exam question for Fortinet's NSE7_PBC-7.2 exam
Question #: 25
Topic #: 1
[All NSE7_PBC-7.2 Questions]

Which two statements are true about Transit Gateway Connect peers in anlPv4 BGP configuration'? (Choose two.)

Show Suggested Answer Hide Answer
Suggested Answer: A, C

For Transit Gateway Connect peers in an IPv4 BGP configuration, the correct statements are:

The inside CIDR blocks are used for BGP peering (Option A): In a BGP configuration for Transit Gateway Connect, the inside CIDR blocks, typically within the 169.254.0.0/16 range, are designated for the BGP peering connections. These blocks are reserved for internal network protocols and are commonly used in AWS for automatic IP address assignment within managed networking services.

You must specify a /29 CIDR block from the 169.254.0.0/16 range (Option C): It is a requirement to specify a /29 CIDR block within the 169.254.0.0/16 range for setting up the network interfaces that facilitate BGP peering. This specific range allows for the necessary number of IP addresses to establish BGP sessions effectively between the transit gateway and on-premises or other virtual appliances.


Contribute your Thoughts:

Chara
1 months ago
I'm not sure about that. I think it might be C and D because you need to specify a /29 CIDR block from the 169.254.0.0/16 range.
upvoted 0 times
...
Irene
1 months ago
Ha! I bet the right answers are A and C. Gotta love those obscure IP ranges for networking stuff.
upvoted 0 times
Lorenza
7 days ago
Exactly, and don't forget to configure the second address from the IPv4 range as the BGP IP address.
upvoted 0 times
...
Jestine
15 days ago
So we need to use inside CIDR blocks for BGP peering and specify a /29 CIDR block from the 169.254.0.0/16 range.
upvoted 0 times
...
Erinn
20 days ago
Yeah, those obscure IP ranges can be tricky to remember.
upvoted 0 times
...
Catina
24 days ago
I always have to double check those CIDR blocks when setting up BGP configurations.
upvoted 0 times
...
Shalon
28 days ago
I think you're right, A and C are the correct answers.
upvoted 0 times
...
Lynelle
29 days ago
Yeah, those obscure IP ranges can be tricky to remember.
upvoted 0 times
...
Lorriane
1 months ago
I think you're right, A and C are the correct answers.
upvoted 0 times
...
...
Nicholle
2 months ago
D is just weird. Why would you need to use the second address in the range? That doesn't make any sense.
upvoted 0 times
...
Marshall
2 months ago
I'm going with A and C. Seems like the most logical choices, unless they're trying to trick us.
upvoted 0 times
...
Barrett
2 months ago
A and C seem like the right answers. I remember learning about the 169.254.0.0/16 range for BGP peering.
upvoted 0 times
Apolonia
10 days ago
Shakira: Yes, those are the two true statements about Transit Gateway Connect peers in an IPv4 BGP configuration.
upvoted 0 times
...
Laine
11 days ago
So, A and C are the correct statements for Transit Gateway Connect peers in an IPv4 BGP configuration.
upvoted 0 times
...
Shakira
15 days ago
That's right. You cannot use IPv6 addresses and you must configure the second address from the IPv4 range on the device as the BGP IP address.
upvoted 0 times
...
Dottie
29 days ago
A and C are correct. The inside CIDR blocks are used for BGP peering and you must specify a /29 CIDR block from the 169.254.0.0/16 range.
upvoted 0 times
...
...
Rickie
2 months ago
I agree with Cheryll. The inside CIDR blocks are definitely used for BGP peering and the second address from the IPv4 range must be configured as the BGP IP address.
upvoted 0 times
...
Cheryll
2 months ago
I think the correct answers are A and D.
upvoted 0 times
...

Save Cancel